Skip to content

Green Galaxy Aurora Force 4 Color Process HSA Water Based Ink Kit

Original price $123.99 - Original price $350.99
Original price
$350.99
$123.99 - $350.99
Current price $350.99
SKU IKWB-AFKIT-G
Size: Gallon Kit

QUART TEMPORARILY SLOW SHIP 

At Green Galaxy, your satisfaction is our top priority. This item is currently not in our Canadian warehouse,  while our slow shipping service may take a little longer, around a 4-6 week timeline, depending on the product, please be assured that our dedicated team is working tirelessly to ensure a seamless delivery experience. From timely updates on your order status to expertly packaged shipments, we're here to make your shopping experience worthwhile.

Four Color Process printing is a technique for printing a life-like design using only four ink colors layered over each other: Cyan, Magenta, Yellow, and Black (or, CMYK).

Kit Includes:

  • Green Galaxy Aurora Force 4 Cyan
  • Green Galaxy Aurora Force 4 Magenta
  • Green Galaxy Aurora Force 4 Yellow
  • Green Galaxy Aurora Force 4 Black

NOTE: Four color process inks are transparent in nature and meant to mix together for a four color process image and not to be printed separately.

Screen Mesh

Can be used with any mesh between 110-355. Recommended at 305 mesh, 65 LPI.

Stencil & Emulsion Guidelines

We recommend using either a water resistant emulsion like Green Galaxy™ CryoCoat and with mesh degreased with Green Galaxy CryoPrep Screen Degreaser. For extended life and long runs it is recommend to post expose the screens or use an emulsion hardener like Ryonet® Harden-X.

Mixing

Be sure to stir product prior to use. You may add 5% finish s to reduce any stick and less build up on bottom of screens for long runs. You may also add are retarder at 5% max as well to increase screen time, but the finish s will help with screen time as well. Please insure a proper cure when adding these products, slows down cure slightly.

Printing

Load screen with plenty of ink. Flood screen prior to printing. Green Galaxy™ HSA Water Based Ink can be printed with a push or pull squeegee stroke. If printing on an automatic, use a medium squeegee blade and medium squeegee pressure, two passes is typically recommended. After printing, flood screen allowing ink to sit on top of image to avoid drying. If screen clogs or exhibits dry ink in the print, re-flood and aggressively print again, this should clear the screen. If it does not clear the screen, spray a small amount of warm water into the stuck areas of the screen and wipe out with a rag. If you are leaving your screen for an extended period of time be sure to leave your screen flooded completely. If your ink begins to scale over, spray with water to wet the ink. Green Galaxyª HSA Water Based Ink can be printed with other water based inks and with plastisol inks.

Flash Curing

For flashing, forced air flash is optimal. Flash until dry to the touch.

Under Base

Light garments, white cotton is optimal, nicer the fabric, better and cleaner result. Coming soon on under print?

Curing Instructions

Printed fabric should be cured for a minimum of 90 seconds at 360°F. Ideally, printed fabric should be cured for three minutes at 300-320°F. When curing with ovens that are smaller, we recommend the use of Green Galaxy™ Drive Low Cure Catalyst to ensure a final cure is achieved after 48 hours.

Testing & Precautions

For cure testing: After set period, perform a stretch test to ensure elasticity. It is always recommended to perform a wash test to ensure proper cure prior to going into production. You may also run abrasion testing to watch for flaking, crocking and test adhesion. Increase cure dwell time if testing fails.

Clean Up

Ink should be removed from screen as soon as printing is completed. General wash-up (on ink that has not dried) can be done with water, though using Sgreenª Aqua Wash is much easier and recommended. For aggressive or dried screens, use Sgreenª Aqua Wash to dissolve ink and blast out areas of stuck ink with water pressure.

Storage

Keep container(s) tightly closed. Store in cool, well-ventilated location that is locked.

General Safety Precautions

 

NOTE:

Four color process inks are transparent in nature and meant to mix together for a four color process image and not to be printed separately.